Tigertronics Signalink Usb Drivers

16-04-2021

Tigertronics Signalink Usb Drivers

W3LFR	Rating:	2020-12-02
Works great on FT8			Time Owned: 0 to 3 months.
Mine is the USB model. It was a slight headache to open the unit and install six jumper wires. Otherwise it was easy to set up and operate with my Kenwood TS-590SG. I like the level controls on the unit so that I don't have to adjust the PC sliders. Both interface cables and a well-written instruction manual were included. They even included a hex key for opening the unit. I'm enjoying FT8 DX for the first time.

W0AWL	Rating:	2020-10-18
On the air in a couple of hours.			Time Owned: 0 to 3 months.
Set up was very easy due to the jumper module, and only two cables to connect. Configuring the FT8 program and making changes in Windows 7 sound control panel was also easy due to the enclosed directions which used pictures to assure you made the correct choice.

W2VS	Rating:	2020-06-07
WELL MADE DEPENDABLE PRODUCT			Time Owned: 0 to 3 months.
I purchased the product just for VHF packet. I installed Winlink Express and the UZ7HO Soundmodem on an HP desktop computer. I am using a Yaesu FT-8800R dual bander. The product comes with all the necessary cables. I highly recommend purchasing the jumper module for $9.95. The unit comes with stripped jumper wires but inserting them is fine work and while not all that difficult if you are not used to that kind of work just get the module. The team at Tigertronics is friendly and helpful. The instructions for the Signalink USB are well written and need to be carefully read! The unit is really a 'set it and forget it' device. I have the TX and RX set at 11 O'clock and have not changed the settings. As recommended DLY is fully counterclockwise. There are many sets of instructions for setting up the Signalink USB with Winlink Express and the UZ7HO Soundmodem. One of the best is W4CA's and can be found at: https://w4ca.com/winlink-express-over-vhf-using-signalink-usb/ Any problems you may encounter are far more likely to be caused by inputting wrong values in the Soundmodem and Winlink Express and not any issue with the TNC. So carefully go through those steps. Also, make sure you install the Soundmodem where it is easy to find! The default location may be difficult to find so install it where it can be found. I highly recommend this product. It works as advertised and I have had no issues with it.

N5OFF	Rating:	2019-01-20
Well made product!			Time Owned: 0 to 3 months.
I bought this product for my return to digital modes after a 25 year break. The documentation is outstanding. I ordered the included cable for my HF rig (Icom) and soldered the jumpers by hand (you can order a jumper bard for your rig but I didn't). Plugged it all in and followed the docs. Worked FB right away. The box and cables are well made and should last a long time. I could not be happier. Thanks Tigertronics. p.s. Great deal from HRO with free shipping.

V47JA	Rating:	2018-08-11
Nice little box			Time Owned: more than 12 months.
I bought the SignaLink about 5 years ago to try 20m DiGi modes. I went on for a couple of hours and hated Digi modes, so I put it in the closet and forgot about it. Fast forward to a couple weeks ago I decided to try FT8, and got it out of the closet and thanks to the help of N5DG and the SignaLink all went easy. Just set the jumpers on the SignaLink for my new radio, plugin a couple cables to the radio and Laptop, and away you go. Nice little box....

KC9SXB	Rating:	2018-08-10
It's a beast			Time Owned: more than 12 months.
I've had this in a pack and hauled, dropped, froze, and used it over the years. It just works! Made my digital life easier, that's for sure. If I were to do it all over again, I'd go with another USB version. Just set the jumpers and forget it is there. What more could you ask for?

K4UX	Rating:	2018-07-24
Quick and easy way to get started in digital			Time Owned: 6 to 12 months.
Decide to give digital modes a try. After reading lots of reviews and consulting friends, decided that this unit would likely be best starter for me. Have been playing with it for about 9 months now. It has performed flawlessly. Easy to order for your specific rig, do initial set-up, and simple connections. Documentation straightforward.

WD9GNG	Rating:	2018-02-24
Easy Setup			Time Owned: 0 to 3 months.
Just got my Signallink-USB with plug in module for my Yaesu FT-857. Instructions were clear and I had it up and running on FLDigi and Digipan within a very short timeframe. Years ago I used a PK-232 for AMTOR, RTTY, and TCPIP in KISS mode but been away from digital for many years. I really enjoy the new digital soundcard modes with waterfall display using the Signallink-USB. Mostly playing with PSK31 at this time but plan to explore more of the exotic ones as time goes by. I appreciate how the Signallink comes with everything you need to get on the air cables and all. It even has a CD with software to get you on the air immediately. Great product!

KK6NTL	Rating:	2017-10-06
Works great but....			Time Owned: more than 12 months.
I have had the unit for over a year and it works great with digital modes. However the XXX knob broke off after only 6 month, Tigertronics would not cover it and the unit still worked so I pressed on. The XXX knob just broke off and the unit is no longer operational. The sole support of these pots is the surface mount solder points on the board.

N6BIZ	Rating:	2017-08-14
Great			Time Owned: more than 12 months.
I have one for the digital modes ITS. GREAT ---------------------- Earlier 5-star review posted by N6BIZ on 2014-05-11 WAY TO EASY TO SET UP ...DOES IT ALL ... NEVER A PROBLEM... WHY BUY ANYTHING ELSE!!!

Tigertronics Signalink Usb Drivers Driver
Tigertronics Signalink Setup
Tigertronics Signalink Usb Drivers Updater
Signalink Driver

Brand: Tigertronics

Manufacturer's Part Number: SLUSBNC-P

The SignaLink USB is a sound card interface that provides the necessary hardware to operate virtually all sound card digital and voice modes, but it does NOT provide the 'CAT' (Computer Assisted Tuning) hardware needed to control the radio. SignaLink USB are set according to the RX Audio/Spkr - 3.5mm Mono Setting The Audio Levels procedure in this manual. If they are too low, then the SignaLink USB will NOT transmit. Computer Connector: USB 1.1/2.0/3.0 Compatible Standard USB 'A'.

Part Type: Digital Mode Interfaces

Product Line: Tigertronics SignaLink™ USB Digital Communications Interface Combos

DXE Part Number: TGR-SLUSBNC-P

Fits Radio Connector Type: No connector

Built-In Rig Control: No

Transmit Level Control: Yes

Receive Level Control: Yes

Transmit Delay Control: Yes

Transmit Status Indicator: Yes

Keying Selection Switch: No

Microphone Pass-Through Input: No

Radio Audio Input Connector: Mono 3.5mm (1/8 in.) female

Radio Speaker Output Connector: Mono 3.5mm (1/8 in.) female

Interface Cable Length: 36.000 in.

Tigertronics signalink usb drivers win 7

Interface Width: 3.200 in.

Interface Height: 1.600 in.

Interface Depth: 3.600 in.

Interface Weight: 0.40 lbs.

USB Cable Included: Yes

Quantity: Sold individually.

Notes: Click on the Documentation tab and the Tigertronics Cables link for crucial details on special transceiver menu settings, internal jumper charts, Plug-N-Play Modules and alternative cables.

Additional Information

Fits Radio Manufacturer	Fits Radio Model	Application Notes
ICOM	IC-251	Must be wired to ICOM 24-pin DIN connector.
ICOM	IC-251A	Must be wired to ICOM 24-pin DIN connector.
ICOM	IC-251E	Must be wired to ICOM 24-pin DIN connector.
ICOM	IC-730	Must be wired to ICOM 24-pin DIN connector.
ICOM	IC-751	Must be wired to ICOM 24-pin DIN connector.
Yaesu	FT-847	Must be wired to 3.5 mm stereo jack for data I/O jack.

Tigertronics SignaLink™ USB Digital Communications Interfaces are sold as Combos, with the interface and interface cable together in a package.
SignaLink™ USB Interfaces support all computer program digital modes and digital voice modes, WITHOUT using your computer sound card! This includes legacy modes, such as RTTY, SSTV, and CW, as well as today's most popular modes, including FT8, PSK31, JT65, JT9, FSK441, MSK144, WSPR, Olivia, EchoLink Node and hundreds more!
Convenient front panel controls let you adjust your Transmit Audio, Receive Audio and Transmit Delay 'on the fly', making operation easy. Tigertronics SignaLink™ USB Interfaces have a state of the art built-in low-noise Analog to Digital sound chip, only one USB connection to the computer and, typically, only one connection to the radio. They are fully isolated and compatible with ALL radio Mic, Accessory and Data Ports.The USB cable is included for connection of the SignaLink™ USB Interface to your computer
Just order the correct combo package of the SignaLink™ USB Interface and Interface Cable for your radio. On the left of your screen, simply select by radio manufacturer and model, or connector type. Click the 'See All' link to open a complete listing of radios supported. Installation of the Tigertronics is a snap, especially if you add an optional Plug-N-Play jumper module that matches your interface and cable selection.
Note: For additional product information, please look at the files under the 'Documentation' tab.
Enjoy operating an entire world of digital modes on your radio with a Tigertronics SignaLink™ USB Digital Communications Interface and Cable Combo from DX Engineering!

Most Helpful Reviews

Fits the bill for portable operation

I needed the smallest, reasonably priced, sound card solution with the fewest cables (2!) that mates up with my FT817 for portable digital operation - the Signalink-USB meets my criteria - great for the DX go bag, especially on international travel.

0 of 0 found this review helpful.

Was this review helpful?Yes|No

Report AbuseClose

If you feel that this review is inappropriate and should be removed from the site, report it to us by clicking the 'Report Abuse' button below.